Fluke 5020A Uživatelský manuál Strana 103
- Strana / 142
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Digital Communications Interface
Commands 6
6-33
The <chn> parameter specifies the channel (1 or 2). A value of 1 is returned if the
specified channel is on. A value of 0 is returned if the specified channel is off.
ROUTe:CLOSe <chn>
Switches on the specified channel.
Example: ROUT:CLOS 1
The <chn> parameter specifies the channel (1 or 2) to switch on. This command may be
password protected (see Password Commands)
ROUTe:OPEN? <chn>
Returns the state of the specified channel.
Example: ROUT:OPEN? 1
Response: 0
The <chn> parameter specifies the channel (1 or 2). A value of 1 is returned if the
specified channel is off. A value of 0 is returned if the specified channel is on.
ROUTe:OPEN <chn>
Switches off the specified channel.
Example: ROUT:OPEN 1
The <chn> parameter specifies the channel (1 or 2) to switch off. This command may be
password protected (see Password Commands)
Calibration Commands
The calibration commands are used to access the sensor calibration parameters. The
calibration commands are always password protected.
CALibrate<chn>:ALERt?
Returns the state of the sensor calibration expired alert enable for the specified channel.
Example: CAL1:ALER?
Response: 0
The CALibrate suffix, <chn>, specifies the channel (1 or 2). A value of 1 is returned if
the calibration alert is enabled for the specified channel. A value of 0 is returned if the
calibration alert is disabled for the specified channel.
CALibrate<chn>:ALERt <bool>
Sets the state of the sensor alert enable for the specified channel.
Example: CAL1:ALER 1
The CALibrate suffix, <chn>, specifies the channel (1 or 2). The <bool> parameter turns
the sensor alert on (1 or ON) or off (0 or OFF). This command is password protected (see
Password Commands).
CALibrate<chn>:DATE:CALibrate?
Returns the sensor calibration date for the specified channel.
Example: CAL1:DATE:CAL?
- Users Manual 1
- Table of Contents 3
- ii 4
- Contents (continued) 5
- iii 5
- iv 6
- List of Tables 7
- vi 8
- List of Figures 9
- viii 10
- Chapter 1 11
- Symbols Used 14
- Safety Information 14
- Safety Information 1 15
- Technical Support 16
- Specifications 17
- Environmental Conditions 18
- Quick Start 19
- Introduction 2 21
- Connect the Power Source 22
- Switch the Power On 22
- Measure Temperature 22
- Parts and Controls 23
- Front Panel 25
- Top Panel 26
- Right Side Panel 26
- Left Side Panel 27
- Back Panel 27
- Quick Buttons 28
- Configurations 28
- Accessories 28
- Accessories 3 29
- General Operation 31
- DC Power Source 33
- Battery 33
- Unit of Temperature 35
- Recording Measurements 35
- Sensors 35
- Menu Functions 37
- Channel Menu 39
- Figure 5-3. Channel Menu 40
- Channel Menu 5 41
- Figure 5-6. Sensor Lock 42
- Display Menu 43
- Figure 5-9. Display Menu 44
- Figure 5-10. Display Setting 44
- Display Menu 5 45
- 5-11 47
- Figure 5-14. Graph Scale 48
- Data Menu 49
- Figure 5-17. Data Record 50
- Data Menu 5 51
- 5-15 51
- 5-17 53
- Figure 5-22. Data Storage 54
- Figure 5-23. Data Clear 54
- 5-19 55
- Figure 5-25. Stats Setting 56
- Figure 5-26. Stats View 56
- 5-21 57
- Figure 5-29. Stats Clear 58
- Figure 5-30. Data Card 58
- 5-23 59
- Alarm Menu 60
- Alarm Menu 5 61
- 5-25 61
- Figure 5-35. Sensor Alarm 62
- System Menu 63
- Figure 5-38. System Menu 64
- Figure 5-39. System Setting 64
- System Menu 5 65
- 5-29 65
- 5-31 67
- Figure 5-43. IR 68
- 5-33 69
- Figure 5-45. System Info 70
- Chapter 6 71
- Communications 73
- Interface Commands 74
- Interface Commands 6 75
- 6-11 81
- Commands 82
- 6-13 83
- 6-15 85
- 6-17 87
- 6-19 89
- 6-21 91
- 6-23 93
- 6-25 95
- 6-27 97
- 6-29 99
- Commands 6 101
- 6-31 101
- 6-33 103
- 6-35 105
- 6-37 107
- 6-39 109
- 6-41 111
- 6-43 113
- 6-45 115
- 6-47 117
- 6-49 119
- 6-51 121
- 6-53 123
- Calibration Procedure 125
- Introduction 127
- Equipment 127
- Preparation 127
- Calibration Points 127
- TSLTSLLTS ∆+= 129
- Chapter 8 131
- Maintenance 133
- Troubleshooting 133
- Downloading Recorded Data 135
- CE Comments 136
- Frequently Asked Questions 136
- Index (continued) 141
Související produkty a manuály pro Měření, testování a kontrola Fluke 5020A
(24 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.124 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce